Quick Start: The light has 3 main levels (High, Medium, and Low) and a beacon-strobe mode.
- When the light is OFF:
- One short-click turns on the light to High
- Two short-clicks turn on the light to Medium
- Three short-clicks turns on the light to the beacon-strobe mode
- Four short-clicks starts the battery indicator mode (see below)
- When the light is ON, a short click turns off the light
Advanced Operation:
- To use another sub-level
- For each of the three main levels (High, Medium, and Low), there are two corresponding sub-levels (H1 and H2, M1 and M2, L1 and L2).
- Go to a main level with short-clicks or press-and-hold
- Double-click to toggle between the two sub-levels (i.e. between H1 and H2, etc.)
- The last sub-levels used in each main level are memorized and will come back on when you go back to that main level. Sub-levels settings are memorized when the light is turned off and through battery changes.
- For each of the three main levels (High, Medium, and Low), there are two corresponding sub-levels (H1 and H2, M1 and M2, L1 and L2).
- Programming the second sub-level
- The first sub-levels (H1, M1, and L1) of each main level have fixed (non-configurable) brightness. The second sub-levels (H2, M2, L2) can be further programmed to different brightness levels.
- Go to a main levels with short-clicks or press-and-hold
- Double-click 6 times to enter the programming mode for that main level
- On subsequent double-clicks the light will cycle through different brightness levels
- When you have the choice you want, exit the programming mode by performing a short-click.
- Second sub-level settings are memorized when the light is turned off and through the battery changes.
- The first sub-levels (H1, M1, and L1) of each main level have fixed (non-configurable) brightness. The second sub-levels (H2, M2, L2) can be further programmed to different brightness levels.
- Changing levels after the light is ON
- When the light is ON, press-and-hold to cycle through Low, Medium, and High. Release at the desired level. Note that the light always cycles from Low regardless which level you are currently in.
- Beacons and Strobes
- The beacon-strobe mode can be accessed from 3 short-clicks when the light is OFF. Once in the beacon-strobe mode, you can double-click to cycle through different types of beacons and strobes. Beacon-strobe settings are memorized when the light is turned off and through battery changes.
- Battery Indicator
- This light uses the main LED (flashing 1 to 4 times) to indicate the estimated remaining capacity of the batteries. To start the battery indicator, short-click 4 times without pause.
Important Safety Considerations
- To reduce the risk of injury, close supervision is necessary when the product is used near children.
- To reduce risk of electrical shock, do not expose battery or internal flashlight components to water or other liquids.
- Use only recommended batteries.
- Remove batteries form flashlight before performing routine maintenance or cleaning.
- Di not disassemble the flashlight. The LED cannot be replaced.
- Do not operate flashlight near flammable liquids or in gaseous or explosive atmospheres. Internal sparks may ignite fumes.
- Do not permit children to use flashlight unsupervised.
- Do not expose battery or internal flashlight components to rain.
- Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water. If liquid gets in oyr eyes, flus them with clean water for at least 10 minutes, then seek immediate medical attention.
- Do not crush, drop or damage batteries. Do not use batteries that have been dropped or received a sharp blow. A damaged battery is subject to explosion. Use a damaged battery can result in serious personal injury.
- Save these instructions. Refer to them frequently and use them to instruct others who may use this product.
Warranty:
ZebraLight, Inc. warrants its products to be free from defects in materials and workmanship. We will repair or replace, at our option, without charge, any products or parts which is found to be defective under normal use and service within 12 months from the date of purchase with proof of purchase. Such repair or replacement shall be the purchaser’s sole and exclusive remedy under this warranty. This warranty does not cover normal maintenance and service and does not apply to any products or parts which have been subject to modification, misuse, abuse, negligence, accident, or improper maintenance or repair by anyone other than ZebraLight.
Our guarantee is unconditional. If any purchase fails to meet your complete satisfaction, for any reason, you may return or exchange it within 30 days of receipt of your shipment. Before returning any product, you MUST obtain a Return Merchandise Authorization number (RMA) from a customer service representative. Include the original invoice received with the merchandise and send the package prepaid, vis UPS or insured USPS Mail to:
ZebraLight, Inc. Attention: Warranty Repair Department 2908 Story Road W Irving, TX 75038 U.S.A.
ZebraLight Flashlight and headlamp products are designed and engineered in the U.S. and manufactured in China. The distinctive shapes of all ZebraLight products are trademarks of ZebraLight, Inc. U.S. and international patents are pending.
Note: The above information is transcribed from a ZebraLight Operator’s Manual as a service and convenience to other cavers. Cascade Grotto is not responsible for the content of this information, nor is this website affiliated with ZebraLight, Inc. in any way, shape, or form. All information is copyright ZebraLight, Inc.